Fit Everything on One Page in Word: Shrink, Margins, Spacing

Find what spills over first: press Ctrl+Shift+8 (Command+8 on a Mac) to show paragraph marks and look at what actually sits on page two. A few real lines usually come back with tighter spacing, smaller margins or Shrink One Page; an empty paragraph, a break or the mark after a table needs a different fix.

What Is on Page Two? Read the Last Page First

Scroll to the end of the document with paragraph marks showing. The overflow almost always falls into one of these groups:

  • A few real lines of text. The page is genuinely a little too full. Spacing, margins or Shrink One Page will pull them back.
  • Only paragraph marks (¶). Empty paragraphs at the end, or blank lines used as spacing, create a page that looks empty. Delete them.
  • A page break or section break. A dotted line labeled as a break forces the next content onto a new page even when there is room. Delete the break if you don’t need it.
  • A single ¶ after a table. If a table runs to the bottom of page one, the paragraph mark Word places after it can land on page two by itself.
  • A picture or chart. One tall object can push everything below it down a page.

Also look at the status bar at the bottom of the window. It normally shows the page count, so you can see the moment a change brings the document back to one page.

Match the Fix to the Cause

What spills over Try first Then
Two to five lines of text Remove extra paragraph spacing Shrink One Page
Half a page or more Edit the text and narrow the margins Smaller font, then Shrink One Page
Empty paragraphs only Delete the ¶ marks Replace blank lines with paragraph spacing
The ¶ after a table Set that mark’s font size to 1 Shrink the table slightly
A page or section break Delete the break Check the paragraph’s page-break settings
A large picture or chart Resize it Change its text wrapping
Font size is fixed by the rules Spacing and margins Cut words

For the table case, Microsoft’s page on deleting a page in Word gives the fix: show paragraph marks, select the mark after the table, select inside the Font size box, type 01 and press Enter. The same page explains a page that starts with a break hidden in paragraph settings: open the paragraph settings from the Home tab, go to Line and Page Breaks, and clear Page break before. If the table itself is too wide or tall, see shrinking a table in Word. For a stray blank page more generally, hiding white space between pages explains which gaps are only a display setting and which are real content.

Add the Shrink One Page Button

Microsoft’s page on shrinking text to fit in Word says the command isn’t shown by default because it isn’t commonly used. To add it in Word for Microsoft 365, Word 2024, 2021, 2019 or 2016 on Windows:

  1. Select Customize Quick Access Toolbar (the small down arrow) and choose More Commands. If you don’t see the toolbar, right-click the ribbon and select Show Quick Access Toolbar first.
  2. Under Choose commands from, select All Commands.
  3. Scroll down to Shrink One Page, select it, then select Add.
  4. Select OK, then select the new button on the toolbar.

Word tries to shrink the document by one page by reducing the size and spacing of the text; Microsoft’s example takes three pages down to two. Two warnings before you click: save a copy first, because the command lowers the size of every font in the document, and while Ctrl+Z undoes it right away, there is no quick way back once you save and close.

It works best when the overflow is small. If it can’t do the job, combine it with the manual fixes below.

Spacing and Margins: Tighten the Layout

Try these before you change the font size.

Paragraph spacing

  1. Select the text (Ctrl+A for everything).
  2. Go to Home > Line and Paragraph Spacing and select Line Spacing Options.
  3. Choose a value in the Line spacing box, and lower the Before and After values.
  4. Select OK.

To remove the gaps between paragraphs across the whole document, Microsoft’s line spacing page also documents Design > Paragraph Spacing > No Paragraph Space. More options are covered in adjusting line spacing in Word, and going all the way to 1.0 is explained in how to single space a Word document.

Margins

Go to Layout > Margins and pick a smaller preset, or select Custom Margins and type exact values. Word’s default is one inch on every side. Printers can’t print right to the edge of the paper, so shave margins a little at a time and check a printout. If your instructions require exact 1-inch margins, leave them alone and use spacing instead. When only one page needs tighter margins, different margins on different pages shows how to limit the change with a section break.

Smaller Text, Narrower Columns, Wider Pages

  • Font size in half points. Select the text and type a value such as 10.5 into the Font size box. Half a point is hard to notice and often frees several lines.
  • A narrower font. Some typefaces fit more characters per line at the same size. Compare a line or two before switching the whole document.
  • Columns for short items. Lists of skills, contacts or short facts waste the right half of the page. Select them and use Layout > Columns.
  • Landscape for one wide page. A wide table or chart may fit better sideways; on a Mac, see making only one page landscape in Word.
  • Edit the words. Merging a one-word last line into the paragraph above, or cutting a sentence, is often the cleanest fix of all.

If you only need a one-page printout and the file itself can stay as it is, printing two pages on one sheet is a print setting rather than a layout change; see printing two pages on one sheet in Word.

Fitting a Resume or Form: What to Cut First

These are style suggestions rather than Word rules. Body text below about 10 points gets hard to read, so cut content before shrinking further. Trim older roles to one or two lines, put contact details on a single line, and use paragraph spacing instead of empty lines between sections so you can tighten everything evenly. Tips for template-based layouts are in editing a resume in MS Word. When the page fits, save a PDF copy so the layout holds on other computers.

Word for the Web and Word for Mac

Word for the web has no Shrink One Page button. Microsoft’s steps: select Editing > Edit Mode in the top-right corner, press Ctrl+A, then select Home > Shrink Font Size until the text fits. Check the result in View > Reading View, or use Open in Word to finish in the desktop app.

Word for Mac customizes its toolbar from the app’s Preferences, under Quick Access Toolbar. Microsoft notes that some commands aren’t supported there yet, so if Shrink One Page isn’t listed, rely on spacing, margins and font size, which work the same way.

The same task in a spreadsheet is a separate setting; see fitting an Excel spreadsheet on one page.

One-page fit questions

Why does Shrink One Page do nothing?

The overflow may be too large, or the extra page may hold only empty paragraphs or a break that shrinking text can’t remove. Clear those first, then try again.

Does Shrink One Page change my margins?

Microsoft describes it as reducing the size and spacing of text. Margins are a separate step under Layout.