How to Use DP Alt Mode in Windows (USB-C to Monitor)

There is no DP Alt Mode switch anywhere in Windows. A USB-C port either carries a DisplayPort video signal or it does not, and Windows uses that mode on its own when the hardware supports it.

So the real job is checking the port: look for the DisplayPort logo beside it or read your PC maker’s spec page, then connect with a full-featured USB-C cable or a USB-C to DisplayPort or HDMI cable. The steps cover Windows 11 first, with Windows 10 differences noted.

Why Windows has no DP Alt Mode setting

DisplayPort Alternate Mode (DP Alt Mode) lets a USB-C connector send a DisplayPort video signal instead of, or alongside, ordinary USB data. Whether a port can do that is decided when the PC is designed: the port has to be wired to the graphics hardware, and the firmware has to support the mode. Nothing in Settings can add that wiring after the fact.

Microsoft says so directly on its page about fixing USB-C problems in Windows: there is no setting to turn on, because the device automatically uses the appropriate mode if it is supported. That page applies to both Windows 11 and Windows 10.

Three pieces have to support the mode at the same time for a picture to appear:

  • The PC’s USB-C port. Some USB-C ports handle only data and charging.
  • The cable or adapter. A charge-only cable, or a cheap adapter, can break the chain.
  • The monitor. It needs a USB-C input that accepts video, or you need an adapter cable to its DisplayPort or HDMI input.

You also do not need a special driver called “DP Alt Mode.” ASUS describes DP Alt Mode connections to its portable monitors as plug and play with no driver to install. What you do need is a current graphics driver and up-to-date firmware, covered in the troubleshooting section.

Check whether your USB-C port can send video

  1. Look at the port. Dell and VESA (the standards group behind DisplayPort) both say ports that support DisplayPort over USB-C normally carry the DisplayPort (DP) logo near the connector. Thunderbolt ports are often marked with a lightning bolt icon; whether they carry video is listed on the spec page in step 3.
  2. Find your exact model. The model name is usually on a sticker underneath a laptop, on the back of a desktop, or on the original box. A general product family name is not enough, since ports can differ between configurations of the same family.
  3. Read the PC maker’s specification page. On the maker’s support site, open the specs for your model and look at the ports list. Wording such as “DisplayPort over USB-C,” “DisplayPort Alt Mode,” “video out,” “Thunderbolt” or “USB4 with display support” means the port can drive a monitor. “USB-C (data only)” or “charging” with no display mention means it cannot.
  4. Note which port. On a PC with two or three USB-C ports, it is common for only some of them to carry video. Write down which one does, so you plug into it every time.
Laptop side view with USB-C ports labeled with DisplayPort and Thunderbolt icons compared to a data-only port
Port icons show which USB-C ports carry video.

Icons vary by maker, and some PCs leave ports unmarked, so treat the spec page as the final word. Dell’s article on DisplayPort over USB Type-C adds that a port without support sends no video to the display, and some USB-C products may show a warning about the incompatibility. VESA’s FAQ adds that trying it will not harm your device.

Desktop PCs are a special case

On a desktop, a USB-C port on the motherboard or a front panel can only send video if it is connected to a video source. That usually means the processor’s built-in graphics, or a separate graphics card whose signal is routed to the port. Board makers handle this differently, so check the motherboard or graphics card manual for the exact requirement. If the manual mentions no display output on USB-C, plan on using the graphics card’s own DisplayPort or HDMI outputs.

Choose the cable or adapter

Once you know the port carries video, match the cable to the monitor’s input.

Monitor input What to connect Things to watch
USB-C with video support A full-featured USB-C cable A charge-only cable will not carry video. The monitor’s manual says which of its USB-C ports accept video.
DisplayPort A USB-C to DisplayPort adapter cable VESA recommends a one-piece adapter cable over a small USB-C to DisplayPort plug adapter plus a separate cable.
HDMI (monitor or TV) A USB-C to HDMI cable or adapter The adapter converts the DisplayPort signal, so the port still has to support DP Alt Mode.
Several screens or extra ports A USB-C or Thunderbolt dock Use a dock, not a hub (see below), and check that the dock is listed as compatible with your PC.

Two details catch people out:

  • Hubs and docks are not the same thing. VESA explains that the USB Implementers Forum defines a “hub” as a product that only supports USB, so a hub cannot pass DP Alt Mode video. Products that carry video as well are called docks.
  • Small receptacle adapters are the weak link. VESA says a USB-C to DisplayPort receptacle adapter is not recommended because it may cause poor picture quality, intermittent operation or no video. A single adapter cable avoids that extra joint.

Connect the monitor and set it up in Windows 11

  1. Turn on the monitor and plug the cable into the USB-C port you identified earlier. Connect it directly to the PC for the first test, without a dock in between.
  2. On the monitor, open its input or source menu and pick the input you are using (USB-C, DisplayPort or HDMI). Menu names vary by monitor model.
  3. Press the Windows logo key + P and choose how Windows should use the screen: PC screen only, Duplicate, Extend or Second screen only.
  4. If the monitor does not appear, open Start > Settings > System > Display, expand Multiple displays and select Detect.
  5. Select Identify to see which number belongs to which screen, drag the boxes to match your desk, and select Apply.

These labels come from Microsoft’s page on using multiple monitors in Windows. For arranging screens, scaling and making a different screen the main display, see extending your display on Windows 11. If you want to switch the second screen off later without pulling the cable, that is covered in disabling a second monitor in Windows 11.

Windows 10 differences

The hardware rules are identical in Windows 10: the same port, cable and monitor checks apply, and there is still no switch to turn on. A few things differ:

  • USB notifications. Microsoft’s Windows 10 path is Start > Settings > Devices > USB, then select or clear Notify me if there are issues connecting to USB devices. Windows 10 also uses different titles for its USB messages than the Windows 11 list below.
  • Display settings. Use Windows logo key + P or Settings > System > Display; Microsoft’s multiple monitors page has a Windows 10 tab with the exact labels.
  • Support status. Windows 10 reached end of support on October 14, 2025. That does not stop a USB-C monitor from working.

What the USB-C messages in Windows 11 mean

When something in the chain does not support the mode, Windows 11 can show a notification. These are the ones that matter for video, with Microsoft’s suggested fixes:

Message What it points to What to try
Display connection might be limited The PC, display or cable may not support DisplayPort or MHL alternate modes, or the connection runs through a hub or dock Confirm all three support the mode and connect the display or dongle directly to the PC
Use different USB port The device may have limited functionality on this port Connect directly to the PC, and try the port your spec page lists for video
Thunderbolt device functionality might be limited The device may not be in the correct USB-C port Connect directly to the PC using its Thunderbolt port
USB4 device functionality might be limited The PC or cable may not support USB4 Check that the PC supports USB4 and use a cable that does
MHL device functionality might be limited Too many USB-C devices or dongles may be connected Unplug other USB-C devices and connect directly

If you never see these messages, check that notifications are on. Microsoft’s route in Windows 11 is to select Search, type usb, open USB settings from the results, and turn Connection notifications on.

When the monitor stays blank

Work through these in order.

  1. Reseat both ends. Unplug the cable at the PC and the monitor, then plug it back in firmly.
  2. Check the monitor’s input. Many monitors do not switch inputs automatically. Select the USB-C, DisplayPort or HDMI input by hand.
  3. Remove the dock or hub. Connect the adapter cable straight to the PC. If the picture appears, the dock or hub was the problem.
  4. Try the other USB-C ports. If only one port works, that is normally the only one wired for video; your spec page should confirm it.
  5. Swap the cable. Borrow a cable known to carry video, ideally a one-piece USB-C to DisplayPort or HDMI cable.
  6. Cycle the display modes. Press the Windows logo key + P and choose Extend or Duplicate. Microsoft’s guide to troubleshooting blank screens also suggests this.
  7. Reset the graphics driver. Press the Windows logo key + Ctrl + Shift + B. The screen may flicker briefly while the driver restarts.
  8. Update drivers and firmware. Run Windows Update, including optional driver updates, then install the latest graphics driver and any BIOS or USB-C and Thunderbolt firmware from your PC maker’s support page. Walkthroughs: updating drivers in Windows 11, updating the graphics driver in Windows 10 and updating the BIOS on Windows 11.

If the picture works but flickers or drops out, try a shorter, better-quality cable and lower the refresh rate or resolution to see whether the link is at its limit.

Resolution, data and charging over one cable

A USB-C connector has four high-speed lanes. VESA describes how DP Alt Mode can use all four for video, or two for video and two for SuperSpeed USB data at the same time. That is why the same monitor can reach a higher resolution or refresh rate on one PC or dock than on another: the PC, cable and monitor decide how many lanes go to video.

VESA and Dell also describe DisplayPort, USB data and USB Power Delivery traveling over one full-featured USB-C cable. A monitor with a USB-C input may therefore charge a laptop while showing its picture, but only if both the monitor and the laptop support that; the monitor’s spec sheet lists how much power its USB-C port supplies. Dell’s figures for the standard (such as high resolutions and charging power) describe what the technology can do, not what every PC delivers.

If your monitor shows the wrong name or you need its model to check its inputs, see checking your monitor model in Windows 10 and 11.

If your port has no DP Alt Mode

When the spec page says the USB-C port is data only, no cable or setting will change that. You still have options:

  • Use a built-in video port. Many laptops and most desktop graphics cards have an HDMI or DisplayPort output. For HDMI, see switching to HDMI on Windows 10, which also covers sending sound to the screen.
  • Use a USB display adapter that installs its own driver. These adapters send the picture as ordinary USB data and rebuild it into video, which needs a driver from the adapter maker. ASUS separates this type of USB-C display connection from DP Alt Mode on its support pages. They can work on ports without DP Alt Mode, but check the adapter maker’s Windows support before buying.
  • Use a different port type on a dock. A dock connected to a Thunderbolt or video-capable port can provide HDMI or DisplayPort outputs. A dock connected to a data-only port cannot.

USB-C video out questions

Is DP Alt Mode the same as Thunderbolt or USB4?

No, but they overlap. DP Alt Mode is one way a USB-C port carries video. Thunderbolt and USB4 are separate USB-C port standards that usually carry DisplayPort video as well. Windows treats them separately, which is why it has separate Thunderbolt and USB4 messages.

Once you have found the right port and cable, label the port or keep the cable with the monitor, so the next connection works on the first try.