How to Put an iPad in an OtterBox Defender Case

OtterBox publishes its own install and removal steps for each Defender Series iPad case, and the steps depend on which iPad model the case fits. Start by finding your iPad’s model number so you can confirm the case matches it. For the standard Defender Series and Defender Series Pro cases, the job is the same: take the case apart, set the iPad in the bottom half of the shell, snap the top half on, then wrap the slipcover back around it.

Match the case and the instructions to your iPad

Defender cases are made for specific iPad models, and OtterBox’s FAQ says its cases are precision-fit to the device. A case made for a similar-looking iPad will not line up, so check two things before you open the box.

Find your iPad’s model number

  1. Open Settings and go to General > About.
  2. Look to the right of Model Number. Apple says this first shows the part number.
  3. Tap the part number to reveal the model number, which starts with “A”.
  4. Compare it with Apple’s list on the Identify your iPad model page to get the iPad’s full name, such as iPad (A16) or iPad (10th generation).

Apple’s model number help page adds that some iPads also print the model number on the back, which helps if the iPad will not turn on.

Find the instruction sheet for your case

The case box and the product page name the case line. OtterBox keeps every Apple install sheet and video on its Apple instructions page. The iPad section lists these Defender entries:

Case name on the box Which steps to follow
Defender Series (Tablet) The six steps in the next two sections, then the stand section
Defender Series Pro (Tablet) The same six steps; OtterBox prints identical wording for both sheets
Defender Series Case with Kickstand, with Kickstand and Hand Strap, or with Folio That case’s own sheet on OtterBox’s page (see the kickstand section below)
Older iPad Pro and iPad (5th gen) Defender cases OtterBox lists a video for these on the same page

For current models, OtterBox’s product pages list compatibility as iPad (A16) and iPad (10th gen) for both the Defender Series and the Defender Series Pro.

Take the Defender case apart

A new Defender arrives assembled, so the first half of the job is taking it apart. These are OtterBox’s first three steps for the Defender Series and Defender Series Pro, in OtterBox’s order and wording.

  1. Release corners and remove shield stand. The shield stand is the hard cover that sits over the screen.
  2. Peel away and remove the outer slipcover. This is the soft outer layer that wraps around the hard shell.
  3. Separate the shell by locating the indicated arrows and releasing each snap along all four sides. You end up with a top half and a bottom half.

Put the iPad in the case

OtterBox’s next three steps rebuild the case around the iPad:

  1. Place the device into the bottom half of the shell.
  2. Place the shell top half on the device and snap the two pieces together along all edges.
  3. Wrap the slipcover around the shell. OtterBox says to make sure the slipcover is nested in the groove and notches on all sides for a tight, secure fit.

Those six steps are the whole install for these two cases. The next section covers the shield stand.

Set up the shield stand

On the Defender Series and Defender Series Pro, the shield stand does double duty: it covers the touchscreen for carrying and props the iPad up for use. OtterBox’s sheet shows four working positions:

  • Comfortable typing
  • Media viewing
  • Portrait interaction
  • Landscape streaming

To release the stand, OtterBox says to move the stand notch to the lowest position and gently pull towards you, then slide up to close the stand tightly against the back of the case.

Kickstand, hand strap and folio versions

These Defender variants have different parts, so the six steps above are not the whole story. OtterBox publishes a separate instruction sheet for each one on its Apple instructions page. As that sheet lays it out for the kickstand version, the kickstand comes off first and goes back on last, after the slipcover. Follow the sheet for the exact case you own rather than mixing steps from two cases.

Which Defender has a built-in screen protector?

This is the biggest difference between the two current Defender lines for iPad (A16) and iPad (10th gen), and it changes what you should expect to see over the screen.

Case What OtterBox’s product page says
Defender Series A hard internal shell, a soft outer slipcover and a built-in screen protector; a four-position stand that doubles as a touchscreen shield; Apple Pencil storage. OtterBox sells an Alpha Glass screen protector separately.
Defender Series Pro No built-in screen protector is mentioned; raised edges guard the camera and screen; the stand doubles as a touchscreen shield; Apple Pencil storage. OtterBox notes its antimicrobial additive protects the case exterior and does not protect you or the screen.

For other iPad models, check the product page for your exact case, since OtterBox lists features per model.

Take the iPad back out

OtterBox’s sheets do not print a separate removal list. Its first three install steps take the case apart, in this order; after step 3, lift off the shell top half and take the iPad out of the bottom half.

  1. Release the corners and remove the shield stand.
  2. Peel away and remove the outer slipcover.
  3. Separate the shell at the indicated arrows, releasing each snap along all four sides.

What OtterBox does not publish for this case

A few things readers often look for are not in OtterBox’s iPad Defender instructions or product pages:

  • Cleaning steps. OtterBox’s FAQ page answers how to clean an OtterBox phone case, not the iPad Defender. There is no printed cleaning method for the iPad case.
  • Fixes for fit problems. The FAQ says any other products that change the dimensions of the device are not compatible with OtterBox cases. Beyond that, OtterBox prints no troubleshooting list. If a case will not close on a matching iPad, contact OtterBox support.
  • Drop ratings in the instructions. The install sheets cover assembly only.

Defender case questions

Is there a video of the install?

Yes. OtterBox links install videos from its instructions page, including a Defender Series iPad install page. The page shows a video only, with no written steps, so keep the instruction sheet handy too.

Does the Defender hold an Apple Pencil?

Both current product pages list Apple Pencil storage as a feature. Check your case’s own page for how its storage is laid out, since OtterBox describes it per model.

Can I add my own screen protector?

OtterBox sells a glass screen protector separately for the Defender Series. For anything else, keep in mind the FAQ’s precision-fit statement: products that change the device’s dimensions are not compatible with OtterBox cases.

If you are shopping for a phone case too, see how the OtterBox Commuter and Symmetry cases for iPhone 14 compare. And while you are in Settings > General finding the model number, it is a good moment to check how much storage space your iPad has left.