Stages are the handful of DPI values your mouse’s DPI button steps through, and a sniper button (Logitech calls it DPI Shift, Razer calls it Sensitivity Clutch) drops to one low value only while you hold it. You set both in the mouse maker’s own app: Logitech G HUB, Razer Synapse, Corsair iCUE or SteelSeries GG. Then save them to the mouse’s onboard memory so they survive a restart or a move to another PC.
A gaming mouse usually ships with a short ladder of preset values. Each press of the DPI button moves one rung up (or down, on mice with two buttons) and stays there until you press again. The sniper button works differently: it is momentary. Hold it and the sensor drops to a preset low value; let go and it snaps back to whatever stage you were on.
That split is what makes the setup useful. The stages cover the jobs you switch between for minutes at a time, such as desktop work, a fast shooter and a slower strategy game. The sniper value covers the few seconds you need fine control, such as lining up a long-range shot or nudging a selection in a photo editor. Logitech describes its DPI Shift button as acting “like a keyboard shift key”: the lower value lasts exactly as long as the button is held.
The default ladder depends on the model. A few examples from the makers’ own pages:
- Logitech G705: three default levels of 800, 1600 and 3200 DPI, with up to five custom levels (100 to 8200) in G HUB.
- Corsair M65 RGB ULTRA: five preloaded stages from 400 to 3000 DPI, plus a SNIPER / OPTION BUTTON.
- SteelSeries Prime Wireless: five default CPI levels of 400, 800, 1200, 2400 and 3200, each with its own indicator color. SteelSeries uses CPI (counts per inch), which means the same thing as DPI here.
Your own mouse may have more or fewer stages, so check its product page or manual before you plan the ladder.
Plan your stage ladder before you open the app
Two or three stages are often enough. Five widely spaced values sound flexible, but in practice you end up pressing the button several times to get back to the one you wanted. A short, deliberate ladder sticks in your head more easily, and the indicator color then tells you where you are at a glance.
Here is one example layout. The numbers are a starting point to adjust, not a recommendation from any maker:
| Slot | Example value | What it is for |
|---|---|---|
| Stage 1 (default) | 800 | Your main game, where aim matters most |
| Stage 2 | 1600 | Desktop work and browsing on a large or high-resolution screen |
| Stage 3 (optional) | 3200 | A second monitor or quick menu navigation |
| Sniper / DPI shift | 400 | Held only while you need very fine control |
Two habits help. First, make the stage you use most the default one (iCUE, for example, has a Set as Default option for this). Second, keep the sniper value well below your lowest stage so the change is obvious when you press it.
If you are not sure what value your mouse is on right now, read it first with the steps in finding your mouse’s current DPI on Windows 11, then build the ladder around that number.
Logitech G HUB
G HUB holds the DPI levels, the DPI Shift value and the profiles for Logitech G mice.
- Open G HUB and select your mouse.
- Open the Sensitivity (DPI) tab for the mouse. Each DPI speed is a dot on the slider: click anywhere on the slider to add a speed, or click and hold a dot and drag it down to remove it. Logitech allows a maximum of five DPI speeds.
- Set the DPI SHIFT SPEED on the same tab; it is the one speed you cannot drag off the slider. On mice with a dedicated DPI Shift button, such as the G502 family, that button already performs the shift.
- To give the shift to a different button, or to give the DPI Shift button a different job, assign it in G HUB’s button settings. Logitech notes the button can be remapped to other actions, from push-to-talk to media controls.

On a G502 X, each profile can carry its own DPI settings and its own color for each setting, which is how the mouse shows which level you are on.
Razer Synapse
Razer splits the job into Sensitivity Stages (the ladder) and Sensitivity Clutch (the hold-to-slow button). Razer’s support article on adjusting DPI in Razer Synapse gives this route for the stages:
- Open Razer Synapse and select your mouse from the DASHBOARD.
- Go to the PERFORMANCE tab and turn on Sensitivity Stages.
- Select a stage, then move its slider or type the DPI you want. Hover over the slider and select the x/y icon if you want different horizontal and vertical values.
For the sniper behavior, Razer’s steps are:
- In Synapse, select your mouse, then select the button you want to customize.
- Select SENSITIVITY and choose Sensitivity Clutch from the dropdown list.
- Set the clutch DPI with Manual Input, Single Slider or X and Y Sliders, then select SAVE.
Hold the assigned button to drop to the clutch value; release it to return to your stage. Razer adds one condition worth knowing before you rely on it in a match: keep Razer Synapse running in the background, or the clutch does not work.
Corsair iCUE
In iCUE, open your mouse and go to its DPI settings. Corsair’s article on adjusting the DPI of your mouse describes the controls:
- Select the + button in the DPI Presets window to add a preset.
- Use the DPI Stages window to set the value of each stage.
- Open the menu next to a stage and select Activate to use it now, or Set as Default to make it the default stage.
- In the Indicator Colors window, pick a color for each stage so the mouse shows which one is active.
Some Corsair mice have a physical sniper button. The M65 RGB ULTRA, for example, has a SNIPER / OPTION BUTTON plus a DPI UP BUTTON and a DPI DOWN BUTTON. Its manual also describes on-the-fly tuning without the software: hold DPI Up and press the forward button to raise the current stage by 50 DPI, or the back button to lower it. Those changes are saved to the mouse’s onboard memory, and if iCUE is running they go straight into the software profile instead.
SteelSeries GG
SteelSeries mice store CPI levels that you customize in SteelSeries GG (SteelSeries’ support pages write it as “SteelSeries Engine / GG”). On the Prime Wireless, for example, the five defaults each have a color: purple for 400, blue for 800, green for 1200, yellow for 2400 and red for 3200. Open GG, select your mouse and edit the CPI levels there. SteelSeries’ support pages list the defaults per model; how many levels you can keep, and whether your model has a button you can set as a hold-to-slow switch, depends on the mouse.
Keep stages after a restart or on another PC
Settings live in one of two places: in the app’s profile on this PC, or in the mouse’s onboard memory. Software profiles can do more (for example, switching automatically when a game starts), but they only apply while the app is installed and running. Onboard memory travels with the mouse.
Before you start, note one Logitech warning: on the G502 X, installing G HUB replaces the two profiles the mouse ships with (Primary for gaming and a secondary productivity profile). If you liked the factory setup, write its values down first.
To store a profile on a Logitech G mouse, Logitech’s steps are:
- Select the mouse in G HUB and select the settings icon in the top right corner.
- Turn the onboard memory toggle ON.
- Choose the profile you want to save to the mouse’s onboard memory.
Logitech’s article on enabling on-board memory mode explains that this lets you use stored settings, such as a sensitivity level, on another computer without installing G HUB. With G HUB installed, a G502 X can have up to five profiles.
For Razer and Corsair, look for an onboard or device memory option in the app’s settings for your model. SteelSeries lists what each model saves to the mouse; on the Prime, CPI is among the settings that stay on the mouse even when the software is quit or uninstalled. The Razer Sensitivity Clutch is the one feature here that the maker says needs its app running, so a profile saved to the mouse may still need Synapse for the clutch.
Check the Windows side once
Windows does not change the sensor’s DPI, but its pointer settings act on whatever the mouse sends, so an unusual Windows setting makes every stage feel wrong. Microsoft’s page on changing mouse settings puts them here:
- Go to Start > Settings > Bluetooth & devices > Mouse.
- Note the Mouse pointer speed slider. Leaving it alone and doing all tuning with stages keeps each stage predictable.
- Check Enhance pointer precision in the same Mouse window. Microsoft describes it as making the pointer more accurate when the mouse is moving slowly. Because it changes how the pointer responds to hand speed, some players switch it off so each stage feels the same at any speed.
If you would rather slow the pointer down in Windows than on the mouse, the slider and its trade-offs are covered in changing mouse speed in Windows 11 and 10. And if you came here looking for the other DPI, the text and app size of your screen, that is a display setting: see changing display scaling in Windows 11.
- The DPI button jumps past the stage you want. You probably have more stages than you use. Delete the extras in the app so the button only cycles through your plan.
- Stages reset after you unplug the mouse or restart. The values were saved to a software profile, not to the mouse. Save them to onboard memory, or make sure the app starts with Windows.
- The sniper button does nothing. On Razer mice, Synapse must be running. On other mice, check that the button is still assigned to DPI Shift and not to another action.
- The app does not see the mouse. Try another USB port, then reinstall the mouse’s driver; updating the mouse driver walks through it.
- The pointer stutters at every stage. That is lag rather than sensitivity. Work through fixing mouse lag on Windows 11 before changing values again.
Once the ladder feels right, leave it for a few days before adjusting. Small changes every session make it hard for your hand to learn any of them.
DPI stage questions
Do I need the maker’s app running for the stages to work?
Not if the stages are saved to the mouse’s onboard memory; the DPI button then cycles through them on any PC. Features that live only in a software profile, and Razer’s Sensitivity Clutch, need the app running.
Why did my mouse lose its factory stages after I installed the app?
Some apps write their own profiles to the mouse. Logitech says installing G HUB overrides the two default profiles on the G502 X. Recreate the values you liked and save them again.
Can the sniper button do something other than lower DPI?
Yes. On Logitech G mice, the DPI Shift button can be remapped in G HUB to other actions, and on Razer and Corsair mice you choose what each programmable button does in Synapse or iCUE.
Can I have different stages for different games?
Yes, through profiles. Each profile carries its own DPI settings, and apps can switch profiles when a game starts. How many profiles you can keep depends on the mouse; Logitech says a G502 X can have up to five once G HUB is installed.

Kermit Matthews runs Live2Tech from just outside Philadelphia. He is an IT specialist with over 20 years of experience, from a university help desk to small-business IT, IT management and his own consulting practice, and has written tech guides full time since 2020. Steps are checked against the current software on a real device or the maker’s official documentation. More about Kermit.