How to Disable IPv6 in Windows 10 (and When You Should Not)

To disable IPv6 in Windows 10, press Windows key + R, type ncpa.cpl, and press Enter. Right-click your network adapter (Wi-Fi or Ethernet), choose Properties, uncheck Internet Protocol Version 6 (TCP/IPv6), and click OK. Turning IPv6 off can help with VPN leaks, older routers, or apps and games that misbehave on IPv6 networks. Microsoft recommends leaving it on, so the safer middle ground is telling Windows to prefer IPv4 instead.

Wi-Fi adapter Properties dialog with the Internet Protocol Version 6 (TCP/IPv6) checkbox cleared and the OK button highlighted
Uncheck Internet Protocol Version 6 (1) in the adapter’s properties and click OK (2).

Should You Disable IPv6?

Good reasons Reasons to leave it on
Troubleshooting a specific connection or app problem Many internet providers and sites now work best over IPv6
A VPN that doesn’t handle IPv6 and leaks traffic Some Windows components expect IPv6 and may behave unexpectedly without it
An old router or network device with broken IPv6 support Home groups, some peer-to-peer features, and future networks rely on it

If your goal is to use IPv4 first, use the Prefer IPv4 option below instead of turning IPv6 off.

Method 1: Disable IPv6 on One Adapter

  1. Press Windows key + R, type ncpa.cpl, and press Enter. Or go to Settings > Network & Internet > Change adapter options.
  2. Right-click the adapter you use (Wi-Fi or Ethernet) and choose Properties.
  3. Uncheck Internet Protocol Version 6 (TCP/IPv6).
  4. Click OK. The change applies immediately.

To turn IPv6 back on, check the box again.

Method 2: PowerShell (All Adapters or One)

Open PowerShell as administrator and run:

Task Command
See IPv6 status on each adapter Get-NetAdapterBinding -ComponentID ms_tcpip6
Disable on one adapter Disable-NetAdapterBinding -Name "Wi-Fi" -ComponentID ms_tcpip6
Disable on all adapters Disable-NetAdapterBinding -Name "*" -ComponentID ms_tcpip6
Turn it back on Enable-NetAdapterBinding -Name "*" -ComponentID ms_tcpip6

Method 3: Prefer IPv4 Instead of Disabling (Recommended)

Microsoft’s guidance is to adjust IPv6 through the DisabledComponents registry value rather than unchecking the adapter box. Setting it to 0x20 makes Windows prefer IPv4 while keeping IPv6 available.

  1. Open Command Prompt as administrator.
  2. Run:
    reg add "HKLM\SYSTEM\CurrentControlSet\Services\Tcpip6\Parameters" /v DisabledComponents /t REG_DWORD /d 0x20 /f
  3. Restart the PC.
DisabledComponents value Effect
0x20 Prefer IPv4 over IPv6
0x10 Disable IPv6 on non-tunnel interfaces
0x01 Disable IPv6 on tunnel interfaces
0xFF Disable IPv6 on all interfaces except loopback

To undo, delete the value (reg delete "HKLM\SYSTEM\CurrentControlSet\Services\Tcpip6\Parameters" /v DisabledComponents /f) and restart.

Check Whether IPv6 Is Off

  • Run ipconfig in Command Prompt. If IPv6 is disabled, no “IPv6 Address” or “Link-local IPv6 Address” lines appear for that adapter.
  • Or run Get-NetAdapterBinding -ComponentID ms_tcpip6 and check that Enabled shows False.

When Turning Off IPv6 Causes Problems

Some apps or features stopped working after disabling IPv6

Turn IPv6 back on and use the Prefer IPv4 setting (0x20) instead.

IPv6 comes back after an update or VPN install

Some updates and VPN clients re-enable bindings. Recheck with the PowerShell command, or use the registry method, which persists.

My internet stopped working completely

Your network may be IPv6-only (rare at home, more common on some mobile hotspots). Turn IPv6 back on.

More Questions About Turning Off IPv6

Does disabling IPv6 make the internet faster?

Usually not. It can help if IPv6 on your network is misconfigured, but on a working network it makes no noticeable difference.

Is this the same on Windows 11?

Yes. The adapter properties, PowerShell commands, and registry value work the same way.

Should I disable IPv6 for gaming?

Only if a specific game or console connection has problems that go away when IPv6 is off. Otherwise, leave it on.